When you see IKEA Dishwasher Error code i10, your dishwasher is having a problem with the water inlet. There are multiple reasons for water inlet malfunctions, such as a clogged water filter or a blockage in the water line.
The Error i10 code will also appear if the water inlet valve is not open.
Error codes are usually on display on the dishwasher’s control panel. If you see IKEA Dishwasher Error code i10, it is important to troubleshoot the problem to get your dishwasher back up and running.
IKEA Dishwasher Error Code i10
- Water Inlet Problem
The water inlet is the first thing to check if you see IKEA Dishwasher Error code 10. Make sure that the water inlet valve is fully open. If it is not, turn the knob to the open position.
Next, check the water line for any blockages. If you see a blockage, remove it, and run a test cycle to see if the Error i10 code appears again.
- Unclog the Water Filter
If you have a clogged water filter, you’ll need to clean it first. Begin cleaning by removing the dishwasher’s filter and rinsing it under running water. If the filter is particularly dirty, it will require thorough cleaning.
Begin by soaking the filter in a bowl of vinegar for a few minutes before rinsing.
Once the filter is clean, reassemble the dishwasher and run a test cycle to see if the error code 10 is still appearing.
- Check the Water Line for Blockages
Another possible cause of IKEA Dishwasher Error code 10 is a blockage in the water line. To check for this, locate the water line that runs to your dishwasher and ensure there are no kinks or blockages.
If you find any, remove them and run a test cycle to see if the error code 10 is still appearing.
- Clean the Inlet Screen
If neither of these solutions solves the problem, the next thing you’ll need to do is clean the inlet screen. This screen is in the water inlet valve and can become clogged with debris over time.
Remove the screen and rinse it under running water to clean it. A dirty screen usually requires a thorough toothbrush or small brush cleaning.
Once the screen is clean, reassemble the dishwasher and run a test cycle to see if the error code 10 is still appearing.
- Replace the Water Inlet Valve
If the IKEA Dishwasher Error code i10 is still appearing, the next thing you’ll need to do is replace the water inlet valve. This relatively easy repair can be easily carried out with a few tools.
Look for the water inlet valve and disconnect the water line from it. Next, remove the two screws that hold the valve in place and then pull the valve out.
To install the new valve, reverse these steps. Once the new valve is in place, reconnect the water line and run a test cycle to see if the error code i10 is still appearing.
These are the most common causes of IKEA Dishwasher Error code i10. If you’ve tried all these solutions and the error code still appears, you may need to call a repair technician.
- Reset the Dishwasher:
If you’ve tried all these solutions and the error code still appears, consider resetting the dishwasher. Initiate resetting by Unplugging the dishwasher from the power outlet and then waiting for 30 seconds.
After 30 seconds have passed, plug the dishwasher back in and run a test cycle to see if the error code is.
To Prevent the i10 Error Code:
To prevent the IKEA Dishwasher Error code i10 from reappearing again, it is important to clean the dishwasher regularly. This includes cleaning the filters, inlet screen, and water line.
The dishwasher water inlet valve must be fully open when the dishwasher is in use. Following these step-by-step tips, you can keep your dishwasher running smoothly for years.
Once you figure out the exact cause of this error, it is easy to fix it. Make sure the water inlet valve is in good health. Regularly clean the dishwasher to avoid these issues.
An error code mostly indicates a faulty part; fixing the malfunctioning part helps eliminate the error.
